//Pi Zero parametric box design with camera support
//R.J.Tidey 17th May 2016

// General parameters
//build 1=base, 2=lid, 3=both
build = 3;
//camera 0=none, 1=internal, 2=external
camera = 2;
//GPIO 0=no cut_out, 1=top cut_out, 2 side cut out
gpio = 1;
wall = 2.0;
hdmi_recess = 1;
corner = 3.0;
tol = 0.3;
$fn=50;


//Base parameters
//inner dimensions
base_width = 30;
//65 for original pizero with no camera connector
//67 for pizero with camera connector
//70  to give more radius for bending cable back internally
base_length = camera==1 ? 70.0 : 67.0;
hole2hole_l = 58;
hole2hole_w = 23;

hdmi_recess_w = 17.5;
hdmi_recess_h = 3.75;

support_offset = 3.5;
support_height = 1.0;
support_radius = 1.4;
support_size = 7.0;
usbpower_offset = 54.0;
usbusb_offset = 41.4;
usb_length = 9.25;
hdmi_offset = 12.4;
hdmi_length = 13.75;
cutout_height_offset = 1.0;
sd_offset = 16.7;
sd_width = 13.0;

//Lid parameters
//1.5 for no camera shallow
//6 for camera
lid_height = camera==1 ? 6.0 : 1.5;
board_thick = 1.35;
connector_thick = 3.2;
screw_depth = 8.0;
screw_radius = 1.3;
gpio_centre_x = 32.5;
gpio_centre_y = 3.5;
gpio_length = 51.5;
gpio_width = 6;
gpio_recess_h = 1.2;
corner_size = 2.4;

//Camera parameters,
camera_hole = 10;
camera_x = 20.0;
camera_screw_centre_offset = 0.0;
camera_screw_x = 12.5;
camera_screw_y = 21.0;
camera_screw_r = 1.5;
camera_cable_y = 20.0;
camera_cable_h = 1.0;

//calculate required base_height
base_height = support_height + board_thick + connector_thick + tol;
echo("base_height = ",base_height);
echo("base_length = ",base_length);
echo("lid_height = ",lid_height);

module round_cube(start,length,width,height,z_offset,cor) {
    hull() {
        translate([start,start,z_offset])
            cylinder(height+wall,r=cor);
        translate([start+length,start,z_offset])
            cylinder(height+wall,r=cor);
        translate([start+length,start+width,z_offset])
            cylinder(height+wall,r=cor);
        translate([start,start+width,z_offset])
            cylinder(height+wall,r=cor);
    }
}

module screwhole() {
    cylinder(wall+support_height+tol,r=support_radius);
    cylinder(wall*0.75,2*support_radius,support_radius);
}

module corner_support() {
    difference() {
        union() {
            round_cube(corner-2*tol,corner_size,corner_size,lid_height,0,corner);
            translate([support_offset,support_offset,wall-0.1])
                cylinder(lid_height+connector_thick+0.1,4,3);
        }
        translate([support_offset,support_offset,wall+lid_height+connector_thick-screw_depth])
            cylinder(screw_depth+1,r=screw_radius);
    }
}

module cut_outs(height) {
    translate([tol+hdmi_offset-0.5*hdmi_length,-wall-0.1,height])
        cube([hdmi_length, wall+ 1.0,base_height]);
    translate([tol+usbusb_offset-0.5*usb_length,-wall-0.1,height])
        cube([usb_length, wall+ 1.0,base_height]);
    translate([tol+usbpower_offset-0.5*usb_length,-wall-0.1,height])
        cube([usb_length, wall+ 1.0,base_height]);
    translate([-wall-0.1,tol+sd_offset-0.5*sd_width,height])
        cube([wall+ 1.0,sd_width,base_height]);
    if(hdmi_recess==1) {
        translate([tol+hdmi_offset-0.5*hdmi_recess_w,-wall-0.1,wall])
            cube([hdmi_recess_w, wall+ 0.1,base_height]);
    }
    if(camera==2) {
        translate([base_length - 2* wall,tol+0.5*(base_width-camera_cable_y),height])
            cube([4*wall,camera_cable_y,camera_cable_h]);
    }
    if(gpio==2) {
        translate([tol + gpio_centre_x - gpio_length*0.5,tol+base_width-wall,height])
            cube([gpio_length,4*wall,base_height]);
    }
}

module base_shell() {
    difference() {
        round_cube(corner-wall,base_length+2*tol+2*wall-2*corner,base_width+2*tol+2*wall-2*corner,base_height,0,corner);
        round_cube(corner-tol,base_length+4*tol-2*corner,base_width+4*tol-2*corner,base_height,wall,corner);
    }
    translate([-tol,-tol,0])
        cube([support_size,support_size,support_height+wall]);
    translate([hole2hole_l+tol,-tol,0])
        cube([support_size,support_size,support_height+wall]);
    translate([hole2hole_l+tol,hole2hole_w+tol,0])
        cube([support_size,support_size+2*tol,support_height+wall]);
    translate([-tol,hole2hole_w+tol,0])
        cube([support_size,support_size+2*tol,support_height+wall]);
 }

module base() {
    difference() {
        base_shell();
        translate([tol+support_offset,tol+support_offset,-0.1]) screwhole();
        translate([tol+support_offset+hole2hole_l,tol+support_offset,-0.1]) screwhole();
        translate([tol+support_offset+hole2hole_l,tol+support_offset+hole2hole_w,-0.1]) screwhole();
        translate([tol+support_offset,tol+support_offset+hole2hole_w,-0.1]) screwhole();
        cut_outs(wall+support_height+board_thick-tol);
    }
}


module lid_shell() {
    difference() {
        round_cube(corner-wall,base_length+2*tol+2*wall-2*corner,base_width+2*tol+2*wall-2*corner,lid_height,0,corner);
        round_cube(corner-tol,base_length+4*tol-2*corner,base_width+4*tol-2*corner,lid_height,wall,corner);
        if(gpio==1) {
            translate([tol+gpio_centre_x-0.5*gpio_length,tol+gpio_centre_y-0.5*gpio_width,-0.5])
                cube([gpio_length,gpio_width,wall+1.0]);
        }
        if(camera==1) {
            translate([tol+camera_x,tol+0.5*(base_width-camera_hole),-0.5])
                cube([camera_hole,camera_hole,wall+1.0]);
            translate([tol+camera_x+0.5*camera_hole+camera_screw_centre_offset,tol+0.5*base_width,-0.5]){
                translate([0,-0.5*camera_screw_y,0]) cylinder(wall+1.0,camera_screw_r,camera_screw_r);
                translate([0,0.5*camera_screw_y,0]) cylinder(wall+1.0,camera_screw_r,camera_screw_r);
                translate([-camera_screw_x,-0.5*camera_screw_y,0]) cylinder(wall+1.0,camera_screw_r,camera_screw_r);
                translate([-camera_screw_x,0.5*camera_screw_y,0]) cylinder(wall+1.0,camera_screw_r,camera_screw_r);
            }
        }
    }
}

module lid() {
    difference() {
        union() {
            lid_shell();
            translate([0,0,0]) corner_support();
            translate([hole2hole_l,0,0]) corner_support();
            translate([hole2hole_l,hole2hole_w,0]) corner_support();
            translate([0,hole2hole_w,0]) corner_support();
        }
        if(hdmi_recess==1) {
            translate([tol+hdmi_offset-0.5*hdmi_recess_w,base_width+tol+0.1,lid_height+wall-hdmi_recess_h])
                cube([hdmi_recess_w, 2*wall,hdmi_recess_h+1]);
        }
        if(gpio==2) {
            translate([tol + gpio_centre_x - gpio_length*0.5,-wall,lid_height+wall-gpio_recess_h])
                cube([gpio_length,4*wall,gpio_recess_h+1]);
        }
    }
}

if (build == 1 || build == 3) {
    base();
}
if (build == 3) {
    translate([0,base_width+4*wall,0]) lid();
}
if(build == 2){
    lid();
}